Difference between revisions of "KISS Konsole Requests"

From HPSDRwiki
Jump to: navigation, search
Line 43: Line 43:
 
16. Add Tx MOX and duplex control- Phil VK6APH  
 
16. Add Tx MOX and duplex control- Phil VK6APH  
  
17. Add Tx drive level control plus band-by-band gain and save in KK.csv - Phil VK6APH '''DONE, for V1.0.5 release'''
+
17. Add Tx drive level control plus band-by-band gain and save in KK.csv - Phil VK6APH - '''DONE, for V1.0.5 release'''
  
 
18. Add Penny J6 pin controls - Phil VK6APH  
 
18. Add Penny J6 pin controls - Phil VK6APH  

Revision as of 06:52, 31 July 2009

KISS Konsole - Feature Requests This is the place to enter your 'dreams' for enhancements. Progress will be indicated by indented responses. Please feel free to do any of this!


7. Add provision to "lock" spectrum and tune Mercury (and Penelope) within that window. This would conceptually be something like the second receiver function in PowerSDR. This could be useful, for example, in a CW contest where you don't want the spectrum display to move around when you pounce on another station. Or a RTTY contest, where you just want to see the data sub-band,or SSB...

Comment - simpler to add a second receiver I think. VK6APH 08:52, 2 June 2009 (UTC)


Current Wish List - 31 July 2009 (what, volunteer and status)


1. Improve the AGC performance, add user controls - George K9TRV

2. Add Penny config on Setup form and run I2C commands to set it up - Phil VK6APH - DONE, for V1.0.5 release

3. Add tabs to the Setup form and group controls onto relevant tabs - George K9TRV - DONE, for V1.0.5 release

4. Add Tx filter bandwidth control to the Setup form - Phil VK6APH - DONE, for V1.0.5 release

5. Add full split frequency duplex facility in FPGAs - Phil VK6APH

6. Show Power output on meter when on transmit

7. Add mic gain/AGC settings contol to Setup form

8. Add CW keyer/Memory keyer etc

9. Allow Setup of CW note frequency (presently fixed at 700Hz) - Mark W8XR

10. Add multi band EQ for both Tx and Rx

11. Add RF speech processor (have an idea from Peter G3PLX that is interesting) also see the program written by Alex VE3NEA since it has a great GUI see http://www.dxatlas.com/VShaper/

12. Add VOX, anti VOX and Noise gate controls

13. Add second receiver within the bandscope bandwidth.

14. Add second independant frequency/bandwidth receiver in the Mercury FPGA (after 5 is done) - Phil VK6APH

15. Add Tx tune control with level as a percentage of gain/band - Phil VK6APH

16. Add Tx MOX and duplex control- Phil VK6APH

17. Add Tx drive level control plus band-by-band gain and save in KK.csv - Phil VK6APH - DONE, for V1.0.5 release

18. Add Penny J6 pin controls - Phil VK6APH

19. Add frequency and level calibration controls

20. Add transverter controls.



Test Equip?

Could some of this code be used as digital test software for the HPSDR board set? I can imagine sending various 'commands' and testing for the 'correct' response. Richard Ames, VK2NRA 21:11, 2 June 2009 (UTC)

Fingerprinting?

I can for-see doing fingerprinting of signals. Think of the advantage in contests if the computer 'automagically' tagged each of the signals on the bandscope with a callsign and changed the colour depending on whether you have logged a contact with them.... the rules will probably outlaw it!  :-) Regards, Richard Ames, VK2NRA 22:46, 2 June 2009 (UTC)