Difference between revisions of "Using WSPR on Microsoft Windows XP, Vista, or Windows 7"

From HPSDRwiki
Jump to: navigation, search
m (Added traditional audio in and out should be tried first)
(Final copy done)
Line 1: Line 1:
'''WSPR 2.1 Overview'''
+
'''WSPR Overview'''
 +
 
 +
WSPR (pronounced "whisper") stands for “Weak Signal Propagation Reporter.” The WSPR software is designed for probing potential radio propagation paths using low-power beacon-like transmissions. WSPR signals convey a callsign, Maidenhead grid locator, and power level using a compressed data format with strong forward error correction and narrow-band 4-FSK modulation. The protocol is effective at signal-to-noise ratios as low as –28 dB in a 2500 Hz bandwidth. Receiving stations with internet access may automatically upload reception reports to a central database. The WSPRnet web site provides a simple user interface for querying the database, a mapping facility, and many other features.
 +
 
 +
'''WSPR 2.1'''
  
 
WSPR 2.1 is the latest version WSPR, the “Weak Signal Propagation Reporter.” It differs from WSPR 2.0 by including support for software defined radios (SDRs) like the HPSDR/PowerSDR rig. With I/Q mode enabled, the program uses 2-channel sampling at 48000 Hz for both input and output. Your HPSDR PowerSDR sends I and Q baseband signals to the WSPR 2.1 input; the WSPR2.1 audio output, also in I/Q format, goes to the HPSDR PowerSDR Tx audio port. T/R switching is accomplished via a virtual serial port. You will need Virtual Audio Cables and Virtual Serial Ports to finish the implementation. Experience has indicated that the traditional audio in and out should be tried first to establish a performance baseline before the I/Q implementation is attempted.
 
WSPR 2.1 is the latest version WSPR, the “Weak Signal Propagation Reporter.” It differs from WSPR 2.0 by including support for software defined radios (SDRs) like the HPSDR/PowerSDR rig. With I/Q mode enabled, the program uses 2-channel sampling at 48000 Hz for both input and output. Your HPSDR PowerSDR sends I and Q baseband signals to the WSPR 2.1 input; the WSPR2.1 audio output, also in I/Q format, goes to the HPSDR PowerSDR Tx audio port. T/R switching is accomplished via a virtual serial port. You will need Virtual Audio Cables and Virtual Serial Ports to finish the implementation. Experience has indicated that the traditional audio in and out should be tried first to establish a performance baseline before the I/Q implementation is attempted.
Line 9: Line 13:
 
2. Install at least two sets of com0com ports for use with PTT and frequency control. [http://sourceforge.net/projects/com0com/ Learn about and install com0com].
 
2. Install at least two sets of com0com ports for use with PTT and frequency control. [http://sourceforge.net/projects/com0com/ Learn about and install com0com].
  
3. Download  and follow the latest version of the Set-Up instructions from the [[Media: Jt65-hf-setup.pdf|JT65HF Setup and Use Guide]].
+
3. Install Virtual Audio Cable (VAC). Follow FlexRadio instructions at: [http://kc.flex-radio.com/KnowledgebaseArticle50230.aspx How to Setup Virtual Audio Cable (VAC) 4.0x with PowerSDR 1.x]
 
+
a. Before testing the PTT button, be sure that "DTR" is checked. The alternative PTT method is not required.
+
 
+
b. For best decoding of weak signals, PowerSDR's AGC should be set to custom and the AGC-T adjusted for 0dB audio input level.
+
 
+
4. Install Virtual Audio Cable (VAC). Follow FlexRadio instructions at: [http://kc.flex-radio.com/KnowledgebaseArticle50230.aspx How to Setup Virtual Audio Cable (VAC) 4.0x with PowerSDR 1.x]
+
 
+
5. Change the calibration values as described in the FlexRadio Knowledge Base article:[http://kc.flex-radio.com/KnowledgebaseArticle50362.aspx How to Configure WSJT with PowerSDR and VAC]
+
  
6. Frequency and band changes are still done manually at this date.
+
4. Change the calibration values as described in the FlexRadio Knowledge Base article:[http://kc.flex-radio.com/KnowledgebaseArticle50362.aspx How to Configure WSJT with PowerSDR and VAC]
  
 +
5. For best decoding of weak signals, PowerSDR's AGC should be set to custom and the AGC-T adjusted for 0dB audio input level.
  
 
[[Category:PowerSDR]]
 
[[Category:PowerSDR]]

Revision as of 13:39, 27 October 2010

WSPR Overview

WSPR (pronounced "whisper") stands for “Weak Signal Propagation Reporter.” The WSPR software is designed for probing potential radio propagation paths using low-power beacon-like transmissions. WSPR signals convey a callsign, Maidenhead grid locator, and power level using a compressed data format with strong forward error correction and narrow-band 4-FSK modulation. The protocol is effective at signal-to-noise ratios as low as –28 dB in a 2500 Hz bandwidth. Receiving stations with internet access may automatically upload reception reports to a central database. The WSPRnet web site provides a simple user interface for querying the database, a mapping facility, and many other features.

WSPR 2.1

WSPR 2.1 is the latest version WSPR, the “Weak Signal Propagation Reporter.” It differs from WSPR 2.0 by including support for software defined radios (SDRs) like the HPSDR/PowerSDR rig. With I/Q mode enabled, the program uses 2-channel sampling at 48000 Hz for both input and output. Your HPSDR PowerSDR sends I and Q baseband signals to the WSPR 2.1 input; the WSPR2.1 audio output, also in I/Q format, goes to the HPSDR PowerSDR Tx audio port. T/R switching is accomplished via a virtual serial port. You will need Virtual Audio Cables and Virtual Serial Ports to finish the implementation. Experience has indicated that the traditional audio in and out should be tried first to establish a performance baseline before the I/Q implementation is attempted.

Installation

1.0 WSPR 2.1 can be downloaded from the WSJT Home Page. Click on the WSPR link at the left margin and then on the appropriate download link. Install the program in the usual way for your operating system. Under Windows, execute the downloaded file and follow the installation instructions. During a test period you may wish to have both WSPR 2.0 and WSPR 2.1 available on your computer; in this case you should install WSPR 2.1 in a new directory, for example the Windows folder C:\HamRadio\WSPR21. (In the Vista or Windows 7 operating systems, if you use the default location C:\Program Files\WSPR you may need to set some access permissions explicitly.)

2. Install at least two sets of com0com ports for use with PTT and frequency control. Learn about and install com0com.

3. Install Virtual Audio Cable (VAC). Follow FlexRadio instructions at: How to Setup Virtual Audio Cable (VAC) 4.0x with PowerSDR 1.x

4. Change the calibration values as described in the FlexRadio Knowledge Base article:How to Configure WSJT with PowerSDR and VAC

5. For best decoding of weak signals, PowerSDR's AGC should be set to custom and the AGC-T adjusted for 0dB audio input level.