Difference between revisions of "OZY REVA ALPHA REVLIST"
(→OZY Revision List: back link) |
(→OZY Revision List: remove section) |
||
| Line 1: | Line 1: | ||
| − | + | '''[[OZY]]''' Revision List | |
07032006-1: Move vias in from edge of board - Done N8VB 07/03/2006 | 07032006-1: Move vias in from edge of board - Done N8VB 07/03/2006 | ||
Revision as of 22:15, 7 June 2009
OZY Revision List
07032006-1: Move vias in from edge of board - Done N8VB 07/03/2006
07032006-2: Move vias away from DIN41612 connector mounting holes - Done N8VB 07/03/2006
07032006-3: Pin 5 of R16 needs to go to +3.3VD, not +3.3VBUS - Done N8VB 07/03/2006
07052006-1: Pin 35 of CY7C68013A needs to be grounded - Done N8VB 07/05/2006
07052006-2: Pin 101 of CY7C68013A needs to be tied to +3.3VD - Done N8VB 07/05/2006
07052006-3: Add HPSDR and TAPR logos - Done N8VB 10/06/2006
07052006-4: Add scope grounding loop - Done N8VB 10/05/2006
07052006-5: Modify for possible use with EP2C8 device? - Need to reassign pins 32,36 and 119,120 for EP2C8 Done N8VB 09/21/2006
07062006-1: Add jumper for USB power thru diode? And/or three pin header. - Done N8VB 07/21/2006
07062006-2: Renumber/rename D1, D3-13 so they are sequential - Done N8VB 07/21/2006
07062006-3: Increase line width on S/N area and other silk items - Done N8VB 07/21/2006
07072006-1: Review OSC1, OSC2 footprints - see page 963 DKT062 ECS Done N8VB 09/21/2006
07172006-1: Review 24 MHz xtal part number. Need to select low profile xtal instead of current one. - Use ECS-240-16-4, DK X441-ND
07172006-2: Make the "a" silkscreen near diodes more readable by changing to a "+" sign. - Done N8VB 07/21/2006
07212006-1: Change pad for D2 from 0805 to SOD-323 decal. - Done N8VB 09/21/2006
07212006-2: Add 10k pullup to nSTATUS line from FPGA. - Done N8VB 07/21/2006
07212006-3: Change nets on pin 14 and pin 15 of U7. They are backwards. - Done N8VB 07/21/2006
07212006-4: Rename pin 103 of the FPGA to FPGA_RXD. Rename pin 104 of the FPGA to FPGA_TXD. - Done N8VB 07/21/2006
07253006-1: Fix DIN41612 symbol to footprint mapping... rows A and C are reversed. - Done N8VB 09/21/2006
07252006-2: Look at whether resistor packs R11 and R14 are big enough to dissipate all LEDs on. - They are OK Done N8VB 09/21/2006
08182006-1: Move LEDS 1,3-8 to extra IO pins on FPGA instead of using GPIO1-8? - Need to reassign GPIF pins Done N8VB 09/21/2006
08192006-1: Move I2C bus connection from C bus to A bus - Janus is looking for I2C on A Bus (from kd5tfd) - Done N8VB 09/21/2006
09212006-1: For EP2C8 use EPS4 configuration device, same pinout as EPS1 - Done N8VB 09/21/2006
